What do you advice for shell usage?

  • Do you use bash? If not, which one do you use? zsh, fish? Why do you do it?
  • Do you write #!/bin/bash or #!/bin/sh? Do you write fish exclusive scripts?
  • Do you have two folders, one for proven commands and one for experimental?
  • Do you publish/ share those commands?
  • Do you sync the folder between your server and your workstation?
  • What should've people told you what to do/ use?
  • good practice?
  • general advice?
  • is it bad practice to create a handful of commands like podup and poddown that replace podman compose up -d and podman compose down or podlog as podman logs -f --tail 20 $1 or podenter for podman exec -it "$1" /bin/sh?

Background

I started bookmarking every somewhat useful website. Whenever I search for something for a second time, it'll popup as the first search result. I often search for the same linux commands as well. When I moved to atomic Fedora, I had to search for rpm-ostree (POV: it was a horrible command for me, as a new user, to remember) or sudo ostree admin pin 0. Usually, I bookmark the website and can get back to it. One day, I started putting everything into a .bashrc file. Sooner rather than later I discovered that I could simply add ~/bin to my $PATH variable and put many useful scripts or commands into it.

For the most part I simply used bash. I knew that you could somehow extend it but I never did. Recently, I switched to fish because it has tab completion. It is awesome and I should've had completion years ago. This is a game changer for me.

I hated that bash would write the whole path and I was annoyed by it. I added PS1="$ " to my ~/.bashrc file. When I need to know the path, I simply type pwd. Recently, I found starship which has themes and adds another line just for the path. It colorizes the output and highlights whenever I'm in a toolbox/distrobox. It is awesome.

  • gnuhaut@lemmy.ml
    ·
    8 months ago

    I use bash as my interactive shell. When ~20 years ago or so I encountered "smart" tab completion for the first time, I immediately disabled that and went back to dumb completion, because it caused multi-second freezes when it needed to load stuff from disk. I also saw it refuse to complete filenames because they had the wrong suffix. Maybe I should try to enable that again, see if it works any better now. It probably does go faster now with the SSDs.

    I tried OpenBSD at some point, and it came with some version of ksh. Seems about equivalent to bash, but I had to modify some of my .bashrc so it would work on ksh. I would just stick to the default shell, whatever it is, it's fine.

    I try to stick to POSIX shell for scripts. I find that I don't need bashisms very often, and I've used systems without bash on them. Most bash-only syntax has an equivalent that will work on POSIX sh. I do use bash if I really need some bash feature (I recently wanted to set -o pipefail, which dash cannot do apparently, and the workaround is really annoying).

    Do not use #!/bin/sh if you're writing bash-only scripts. This will break on Debian, Ubuntu, BSD, busybox etc. because /bin/sh is not bash on those systems.

    • DefederateLemmyMl@feddit.nl
      ·
      8 months ago

      Do not use #!/bin/sh if you’re not writing bash-only scripts

      Actually #!/bin/sh is for bourne shell compatible scripts. Bash is a superset of the bourne shell, so anything that works in bourne should work in bash as well as in other bourne compatible shells, but not vice versa. Bash specific syntax is often referred to as a "bashism", because it's not compatible with other shells. So you should not use bashisms in scripts that start with #!/bin/sh.

      The trouble is that it is very common for distros to links /bin/sh to /bin/bash, and it used to be that bash being called as /bin/sh would change its behavior so that bashisms would not work, but this doesn't appear to be the case anymore. The result is that people often write what they think are bourne shell scripts but they unintentionally sneak in bashisms... and then when those supposed "bourne shell" scripts get run on a non-bash bourne compatible shell, they fail.

      • gnuhaut@lemmy.ml
        ·
        8 months ago

        Oh I wanted to say, "Do not use #!/bin/sh if you're not writing bash-only scripts". I think I reformulated that sentence and forgot to remove the not. Sorry about the confusion. You're exactly right of course. I have run into scripts that don't work on Debian, because the author used bashisms but still specified /bin/sh as the interpreter.

        • DefederateLemmyMl@feddit.nl
          ·
          8 months ago

          Oh I wanted to say, “Do not use #!/bin/sh if you’re not writing bash-only scripts”

          Hah, I was wondering if that was wat you actually meant. The double negation made my head spin a bit.

          I have run into scripts that don’t work on Debian, because the author used bashisms but still specified /bin/sh as the interpreter.

          The weird thing is that man bash still says:

          When invoked as sh, bash enters posix mode after the startup files are read.
...
--posix
    Change  the  behavior  of bash where the default operation differs from the POSIX standard to 
    match the standard (posix mode). See SEE ALSO below for a reference to a document that details 
    how posix mode affects bash's behavior.

          But if you create a file with a few well known bashisms, and a #!/bin/sh shebang, it runs the bashisms just fine.